HomeMy WebLinkAboutLA171312 - 17303 Eagleview Dr Permit PackRESIDENTIAL BUILDING PERMIT APPLICATION
PAGE 2
OFFICE USE ONLY
BUILDING PERMIT TYPE REQUIRED INSPECTIONS
SINGLE FAMILY DWELLING BUILDING
DUPLEX AS BUILT
TOWNHOUSE UNITS BUILDING FINAL
DETACHED TOWN HOUSE UNIT DECK FOOTING
CONDO FIREPLACE
ACESSORY BUILDING FOOTING
REROOF FOUNDATION
RESIDE FRAMING
PORCH FRAMING
GARAGES
INSULATION
RES ADDN/REPAIR/RMDL
DECK
PORCH
GARAGES LATH
LOWER LEVEL FINISH LOWER LEVEL FINAL
ADDITION OTHER
FOUNDATION ONLY PORCH FOOTING
MISCELLANEOUS POURED WALL
DEMO SEPTIC TANK REMOVAL
MOVED SITE
MECHANICAL
CITY BUILDING VALUATION: $AIR TEST
FINAL
BUILDING PERMIT FEES ROUGH-IN
$PERMIT FEE PLUMBING
$PLAN CHECK FINAL
$SURCHARGE ROUGH-IN
$METRO SAC METER SIZE
$CITY WATER HOOKUP UNIT PRESSURE REDUCING VALVE
$CITY SEWER HOOKUP UNIT SEWER/WATER
$LANDSCAPE ESCROW SEWER/WATER
$TREE ESCROW FINAL
$MISC ESCROW STREET DRAINTILE
$PLUMBING BUILDING INFORMATION
$MECHANICAL TYPE OF CONSTRUCTION
$SEWER WATER ZONING
$OTHER CODE EDITION
$TOTAL FIRE SUPPRESSION SYSTEM
OCCUPANCY GROUP
APPROVED BY:
BUILDING INSPECTOR: Date:
PLUMBING/MECHANICAL
INSPECTOR: Date:
COMMENTS:
3
air quantity is negative, no additional makeup air will be required for ventilation, if the value is positive refer to
Table 501.4.2 and size the opening. Transfer the cfm, size of opening and type (round, rectangular, flex or rigid)
to the last line of section D. The ventilation make-up air supply must communicate with the exhaust appliances.
Table 501.4.1, 2015 Minnesota Mechanical Code
PROCEDURE TO DETERMINE MAKEUP AIR QUANITY FOR EXHAUST APPLIANCES IN DWELLING
UNITS
(Additional makeup air will be required for combustion appliances, see KAIR method for calculations)
One or multiple power
vent or direct vent
appliances or no
combustion appliances
Column A
One or multiple fan-
assisted appliances
and power vent or
direct vent appliances
Column B
One atmospherically
vented gas or oil
appliance or one solid
fuel appliance
Column C
Multiple
atmospherically
vented gas or oil
appliances or solid
fuel appliances
Column D
1.Enter the Appropriate Column to Estimate House Infiltration
a) pressure factor
(cfm/sf) 0.15 0.09 0.06 0.03
b) conditioned floor area (sf)
(including unfinished basements) 2398
Estimated House Infiltration (cfm):
[1a x 1b] 359
2. Exhaust Capacity ERV= 0
a) clothes dryer (cfm) 135 135 135 135
b) 80% of largest exhaust rating
(cfm);
(not applicable if recirculating
system or if powered makeup air is
electrically interlocked and match
to exhaust)
56
c) 80% of next largest exhaust
rating (cfm);
(not applicable if recirculating
system or if powered makeup air is
electrically interlocked and
matched to exhaust)
NA
Total Exhaust Capacity (cfm);
[2a + 2b +2c] 191
3. Makeup Air Quantity (cfm)
a) total exhaust capacity (from
above)
191
b) estimated house infiltration
(from above) 359
Makeup Air Quantity (cfm);
[3a – 3b]
(if value is negative, no makeup air
is needed)
-168
4. For makeup Air Opening Sizing,
refer to Table 501.4.2
NR
A. Use this column if there are other than fan-assisted or atmospherically vented gas or oil appliance or if there are no combustion
appliances. (Power vent and direct vent appliances may be used.)
B. Use this column if there is one fan-assisted appliance per venting system. (Appliances other than atmospherically vented appliances
may also be included.)
C. Use this column if there is one atmospherically vented (other than fan-assisted) gas or oil appliance per venting system or one solid
fuel appliance.
D. Use this column if there are multiple atmospherically vented gas or oil appliances using a common vent or if there are
atmospherically vented gas or oil appliances and solid fuel appliances.
Be advised: 2015 Minnesota Mechanical Code, Section 505.2, Installation of exhaust hood systems capable of
exhausting in excess of 400 cfm shall be provide with makeup air at a rate approximately equal to the exhaust air
rate. Such makeup air systems shall be equipped with a means of closure and shall be automatically controlled
to start and operate simultaneously with the exhaust system.
Concept Approval ONLY
Subject to Field Inspection
Inspector Date
2015
MN Bldg
Code
07/26/2019dmathews
UFER Ground
-Provide 20' Rebar in footing and stub
up near electrical service panel.
-Min. 15" clearance to anyobstruction from center of
W.C., 24" in front(typ).
07/17/19 X
KP