The URL can be used to link to this page

Home My WebLink AboutLA201133-Approved Benjamin Rietz - ENG CAD-minEverlight Solar, PO Box 930550, Verona, WI 53593 Subject: Structural Certification for Installation of Residential Solar re job:Benjamin Rietz, 20984 Hyacinth Avenue, Lakeville, MN 55044 Attn.: To Whom It May Concern ROOF 1: 115 mph Ground Snow:50 psf C Min Roof Snow:NA psf ROOF 1: Current Renewables Engineering Inc. Professional Engineer projects@creng.solar Code:2018 IBC (ASCE 7-16) Ult Wind Speed: Exposure Cat: After review of the field observation report and based on our structural capacity calculations in accordance with applicable building codes, the existing roof framing supporting the proposed solar panel layout has been determined to be: adequate to support the imposed loads. Therefore, no structural upgrades are required. 3/21/2022 A field observation was performed to document the existing framing of the above mentioned address. From the field observation, the existing roof structure was observed as: Shingle roofing supported by 2x4 Truss @ 24 in. OC spacing. The roof is sloped at approximately 30 degrees and has a max beam span of 8 ft between supports. Design Criteria: 03/21/2022 Everlight Solar PO Box 930550 Verona, WI 53593 Attn.: To Whom It May Concern re job:Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 Design Criteria: Code:2018 IBC ASCE 7-16 Live Load:20 psf Ult Wind Speed:115 mph Exposure Cat:C Ground Snow:50 psf Min Roof Snow:NA Current Renewables Engineering Inc. Professional Engineer projects@creng.solar 3/21/2022 The following calculations are for the structural engineering design of the photovoltaic panels and are valid only for the structural info referenced in the stamped plan set. The verification of such info is the responsibility of others. After review, I certify that the roof structure has sufficient structural capacity for the applied PV loads. All mounting equipment shall be designed and installed per manufacturer's approved installation specifications. 03/21/2022 Job Code: Benjamin Rietz 2 of 6 Roof Properties: Roof Type = Roof Pitch (deg) = Mean Roof Height (ft) = Attachment Trib Width (ft) = Attachment Spacing (ft) = Framing Type = Framing Size = Framing OC Spacing (in.) = Section Thickness, b (in.) = Section Depth, d (in.) = Section Modulus, Sx (in.^3) = Moment of Inertia, Ix (in.^4) = Framing Span (ft) = Deflection Limit D+L (in.) = Deflection Limit S or W (in.) = Framing Upgrade = Sister Size = Wood Species = Wood Fb (psi) = Wood Fv (psi) = Wood E (psi) = CD (Wind) = CD (Snow) = CM = Ct = CL = Ci = CF = Cfu = Cr = F'b_wind (psi) = F'b_snow (psi) = F'v_wind (psi) = F'v_snow (psi) = M_allowable_wind (lb-ft) = M_allowable_snow (lb-ft) = V_allowable_wind (lbs) = V_allowable_snow (lbs) = E' (psi) = 725 1600000 524 1008 207 729 2053 288 1.15 2857 1.5 1.00 1.0 1.6 1.15 180 1600000 DF #2 900 Adequate NA 1.07 8 1.6 3.1 5.4 1.5 3.5 2x4 24 4 Truss 13 2.75 Shingle 30 Roof 1 Job Code: Benjamin Rietz 3 of 6 Load Calculation: Panels Dead Load (psf) = Roofing Weight (psf) = Decking Weight (psf) = Framing Weight (psf) = Misc. Additional Weight (psf) = Existing Dead Load (psf) = Total Dead Load (psf) = Ground Snow Load, pg (psf) = Min Flat Snow, pf_min (psf) = Min Sloped Snow, ps_min (psf) = Snow Importance Factor, Ic = Exposure Factor, Ce = Thermal Factor, Ct = Flat Roof Snow, pf (psf) = Slope Factore, Cs = Sloped Roof Snow, ps (psf) = Ultimate Wind Speed (mph) = Directionality Factor, kd = Topographic Factor, kzt = Velocity Press Exp Factor, kz = Ground Elevation Factor, ke = Velocity Pressure, qz (psf) = Array Edge Factor, ɶE = ^ŽůĂƌƋƵĂůŝǌĂƚŝŽŶ&ĂĐƚŽƌ͕ɶĂс External Pressure Up, GCp_1 = External Pressure Up, GCp_2 = External Pressure Up, GCp_3 = External Pressure Down, GCp = Design Pressure Up, p_1 (psf) = Design Pressure Up, p_2 (psf) = Design Pressure Up, p_3 (psf) = Design Pressure Down, p (psf) =17.1 -38.5 -47.0 0.8 -32.1 -1.8 -2.2 1.25 0.70 -1.5 0.85 1.00 24.4 115 0.85 1.0 Roof 1 35 Wind Load Calculations: 34.65 1.00 Roof 1 1.1 Snow Load Calculations: 50 NA NA 1.0 0.9 6.6 9.6 0.6 1.0 3.0 2.0 Dead Load Calculations: 3.0 Roof 1 Job Code: Benjamin Rietz 4 of 6 Hardware Checks: Ref. Widthrawal Value, W (lb/in) = (CM = Ct = Ceg = 1.0) CD = Adjusted Widthrawal Value, W' (lb/in) = Lag Penetration, p (in.) = Allowable Widthrawal Force, W'p (lbs) = Applied Uplift Force (lbs) = Uplift DCR = Ref. Lateral Value, Z (lbs) = (CM = Ct = Cȴ = Ceg = 1.0) CD = Adjusted Lateral Value, Z' (lbs) = Applied Laeral Force (lbs) = Angle of Resultant Force, ɲ;ĚĞŐͿс Adjusted Interaction Lateral Value, Z'ɲ (lbs) = Lateral DCR = Roof Framing Checks: LC1: D+S Applied Moment (lb-ft) = Applied Shear (lbs) = Allowable Moment (lb-ft) = Allowable Shear (lbs) = Moment DCR = Shear DCR = LC2: D+0.6W Applied Moment (lb-ft) = Applied Shear (lbs) = Allowable Moment (lb-ft) = Allowable Shear (lbs) = Moment DCR = Shear DCR = LC3: D+0.75(S+0.6W) Applied Moment (lb-ft) =462 0.29 0.16 729 1008 212 159 0.90 0.49 524 725 354 Force Checks: Roof 1 472 519 0.40 207 49 1.15 311 0.22 270 1064 -237 426 2.5 266 1.6 Lag Screw Checks: Roof 1 Job Code: Benjamin Rietz 5 of 6 Applied Shear (lbs) = Allowable Moment (lb-ft) = Allowable Shear (lbs) = Moment DCR = Shear DCR = LC4: 0.6D+0.6W Applied Moment (lb-ft) = Applied Shear (lbs) = Allowable Moment (lb-ft) = Allowable Shear (lbs) = Moment DCR = Shear DCR = LC1: D+L Deflection (in.) = Deflection Limit (in.) = Deflection DCR = LC2: S Deflection (in.) = Deflection Limit (in.) = Deflection DCR = LC3: W (Down) Deflection (in.) = Deflection Limit (in.) = Deflection DCR = LC4: W (Up) Deflection (in.) = Deflection Limit (in.) = Deflection DCR = Seismic Check: Wall Weight (psf) = Tributary Wall Area (ft2) = Total Wall Weight (lbs) = Roof Weight (psf) = Roof Area (ft2) = Total Roof Weight (lbs) = 1000 17000 7 2400 15844 0.05 Existing Weight: 17 -0.06 1.23 1.23 0.03 0.12 0.03 0.15 1.23 1.84 0.03 Deflection Checks (Service Level): Roof 1 0.06 0.20 0.11 729 1008 144 108 0.63 0.34 729 1008 346 Job Code: Benjamin Rietz 6 of 6 Total Existing Weight (lbs) = Total Additional PV Weight (lbs) = (Existing W + Additional W)/(Existing W) =104% The increase in weight as a result of the solar system is less than 10% of the existing structure and therefore no further seismic analysis is required. Limits of Scope of Work and Liability: Existing structure is assumed to have been designed and constructed following appropriate codes at time of erection, and assumed to have appropriate permits. The calculations produced are only for the roof framing supporting the proposed PV installation referenced in the stamped planset and were completed according to generally recognized structural analysis standards and procedures, professional engineering and design experience, opinions and judgements. Existing deficiencies which are unknown or were not observable during time of inspection are not included in this scope of work. All PV modules, racking, and mounting equipment shall be designed and installed per manufacturer's approved installation specifications. The Engineer of Record and the engineering consulting firm assume no responsibility for misuse or improper installation. This analysis is not stamped for water leakage. Framing was determined based on information in provided plans and/or photos, along with engineering judgement. Prior to commencement of work, the contractor shall verify the framing sizes, spacings, and spans noted in the stamped plans, calculations, and cert letter (where applicable) and notify the Engineer of Record of any discrepancies prior to starting construction. Contractor shall also verify that there is no damaged framing that was not addressed in stamped plans, calculations, and cert letter (where applicable) and notify the Engineer of Record of any concerns prior to starting construction. Additional PV Weight: 1361 Weight Increase: 32844 Everlight Solar Construction PO Box 930550 Verona, WI 53593 License# DCQ-111802116 833.786.4387 ext. 701 CONTRACTOR INFORMATION: SITE INFORMATION Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC Lat, 44.64597 Long, -93.2496805999999 (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) Xcel Energy MN DATE: March 18, 2022 PV01 COVER PAGE PV02 SITE PLAN PV03 ROOF ATTACHMENTS PV04 MOUNTING DETAIL PV05 LINE DIAGRAM PV06 ELECTRICAL CALCS PV07 LABELS PV08 PLACARD PV09 SITE PHOTOS COVER PAGE - PV01 DRAWN BY: SoloCAD 1.INSTALLATION OF SOLAR PHOTOVOLTAIC SYSTEM SHALL BE IN ACCORDANCE WITH NEC ARTICLE 690, AND ALL OTHER APPLICABLE NEC CODES WHERE NOTED OR EXISTING. 2.PROPER ACCESS AND WORKING CLEARANCE AROUND EXISTING AND PROPOSED ELECTRICAL EQUIPMENT WILL COMPLY WITH NEC ARTICLE 110. 3.ALL WIRES, INCLUDING THE GROUNDING ELECTRODE CONDUCTOR SHALL BE PROTECTED FROM PHYSICAL DAMAGE IN ACCORDANCE WITH NEC ARTICLE 250 4.THE PV MODULES ARE CONSIDERED NON-COMBUSTIBLE; THIS SYSTEM IS UTILITY INTERACTIVE PER UL 1741 AND DOES NOT INCLUDE STORAGE BATTERIES OR OTHER ALTERNATIVE STORAGE SOURCES. 5.ALL DC WIRES SHALL BE SIZED ACCORDING TO [NEC 690.8] 6.DC CONDUCTORS SHALL BE WITHIN PROTECTED RACEWAYS IN ACCORDANCE WITH [NEC 690.31] 7.ALL SIGNAGE TO BE PLACED IN ACCORDANCE WITH LOCAL JURISDICTIONAL BUILDING CODE. PHOTOVOLTAIC (PV) SYSTEM SPECIFICATIONS AERIAL VIEW: SHEET INDEX: OCCUPANCY: R-3 ZONING: RESIDENTIAL STREET VIEW: GENERAL NOTES APPLICABLE GOVERNING CODES SITE SPECIFICATIONS 2020 NEC 2020 MRC 2020 MFC 2020 MBC EQUIPMENT: AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) RACKING: Quickbolt - 48" O.C. M MSP ACC PV JB JB Everlight Solar Construction PO Box 930550 Verona, WI 53593 License# DCQ-111802116 833.786.4387 ext. 701 CONTRACTOR INFORMATION: SITE INFORMATION Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC Lat, 44.64597 Long, -93.2496805999999 (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) Xcel Energy MN DATE: March 18, 2022 EQUIPMENT LEGEND: INVERTERVISIBLE, LOCKABLE, LABELED AC DISCONNECT METER SOCKET (FOR UTILITY PV METER) UTILITY METER MAIN SERVICE PANEL LC LOAD CENTER FIRE ACCESS PATHWAY (3' TYP) C INV PV AC MSP M COMBINER BOX PROPERTY LINEFRONT OF HOME20984 Hyacinth AvenueBATT BATTERY(IES) VISIBLE, LOCKABLE, LABELED AC DISCONNECT LOCATED WITHIN 10' OF UTILITY METER CASE #04896762 $//39(48,30(17,167$//(' :,7+,1 2)87,/,7<0(7(5 81(6&257('.(</(66 $&&(666+$//%(3529,'(' 72;&(/(1(5*<)25$// ;&(/(1(5*<2:1(' 0(7(56$1'',6&211(&76 NO CLEARANCE ISSUES AROUND HOME OR SOLAR ARRAY ELECTRIC SERVICE LINES ARE UNDERGROUND NOT OVERHEAD 62/$5$55$<,19(57(56 %(+,1'3$1(/6 0$,16(59,&(3$1(/ /2&$7(',16,'( SUB SUB PANEL SITE PLAN - PV02 DRAWN BY: SoloCAD MP1 MP2 ARRAY DETAILS: MOUNTING PLANE:AZIMUTH:TILT: MP1 180°30° MP2 180°30° 152'-5" 85'-0"Hyacinth Ave.48.59' W03/21/2022 M MSP ACC PV JB JB EQUIPMENT INFORMATION:ROOF INFO:PHOTOVOLTAIC ARRAY STRUCTURAL CRITERIA: RAIL MANUFACTURER:IronRidge ROOF TYPE:Asphalt Shingle PV MODULE COUNT:25 RAIL PART NUMBER:XR-10 ROOF FRAMING:Manufactured Truss ARRAY AREA:MODULE COUNT * 19.83 ft² = 495.75 ATTACHMENTS Quickbolt RAFTER/TOP CHORD SIZE:2x4 ROOF AREA:2881.807 ft² ATTACHMENT QTY:46 RAFTER/TOP CHORD SPACING:24"PERCENT OF ROOF COVERED:17% SPLICE QTY:4 ATTACHMENT SPACING:48''ARRAY WEIGHT:MODULE COUNT * 45 lbs = 1125 lbs MIDCLAMP QTY:42 DISTRIBUTED LOAD:ARRAY LBS/ATTACHMENTS = 24.46 ENDCLAMP QTY:16 POINT LOAD: (lbs/ft²)(ARRAY) WEIGHT/AREA = 2.27 lbs/ft² Everlight Solar Construction PO Box 930550 Verona, WI 53593 License# DCQ-111802116 833.786.4387 ext. 701 CONTRACTOR INFORMATION: SITE INFORMATION Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC Lat, 44.64597 Long, -93.2496805999999 (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) Xcel Energy MN DATE: March 18, 2022 ROOF ATTACHMENTS - PV03 DRAWN BY: SoloCAD 1'-6"TYP 3'-0"TYP 03/21/2022 5$,/ /)227$77$&+0(17%5$&.(7 (522))5$0,1* 48,&.%2/7 )/$6+,1* 3902'8/( (&2036+,1*/(522)/$<(5 5$,/ (1'&/$03 3902'8/( 0,'&/$03 3902'8/( 0,1 '(37+ 5$,/ 5$,/ )/$6+,1* 48,&.%2/7 2'-8" MIN - 3'-10" MAX 5$,/ 3902'8/( " MAX."1'-8" MAX. FRONT VIEW 10" MIN - 1'-4" MAX2'-8" MIN - 3'-10" MAX 10" MIN - 1'-4" MAX SIDE VIEW (5$)7(5723&+25'6 (5$)7(5723&+25' DETAIL, MOUNTING AND FLASHING END CLAMP DETAILS MID CLAMP DETAILS EQUIPMENT INFORMATION:ROOF INFO:PHOTOVOLTAIC ARRAY STRUCTURAL CRITERIA: RAIL MANUFACTURER:IronRidge ROOF TYPE:Asphalt Shingle PV MODULE COUNT:25 RAIL PART NUMBER:XR-10 ROOF FRAMING:Manufactured Truss ARRAY AREA:MODULE COUNT * 19.83 ft² = 495.75 ATTACHMENTS Quickbolt RAFTER/TOP CHORD SIZE:2x4 ROOF AREA:2881.807 ft² ATTACHMENT QTY:46 RAFTER/TOP CHORD SPACING:24"PERCENT OF ROOF COVERED:17% SPLICE QTY:4 ATTACHMENT SPACING:48''ARRAY WEIGHT:MODULE COUNT * 45 lbs = 1125 lbs MIDCLAMP QTY:42 DISTRIBUTED LOAD:ARRAY LBS/ATTACHMENTS = 24.46 ENDCLAMP QTY:16 POINT LOAD: (lbs/ft²)(ARRAY) WEIGHT/AREA = 2.27 lbs/ft² Everlight Solar Construction PO Box 930550 Verona, WI 53593 License# DCQ-111802116 833.786.4387 ext. 701 CONTRACTOR INFORMATION: SITE INFORMATION Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC Lat, 44.64597 Long, -93.2496805999999 (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) Xcel Energy MN DATE: March 18, 2022 MOUNTING DETAIL - PV04 DRAWN BY: SoloCAD 03/21/2022 4 4 UTILITY PV PRODUCTION METER 4 (N) #A FUSES ##A UTILITY AC DISCONNECT PHOTOVOLTAIC AC DISCONNECT LINE SIDE LOAD SIDE VISIBLE-OPEN TYPE, LOCKABLE, READILY ACCESSIBLE, LABELED, 240V, 2-POLE, FUSED THE PV PRODUCTION METER SOCKET MUST HAVE LEVER BYPASS/BYPASS 1-PH, 3-WIRE, 120/240V, 200A ##A VISIBLE-OPEN TYPE, LOCKABLE, READILY ACCESSIBLE, LABELED, 240V, 2-POLE NO LOADS OR STAGE SYSTEM ON DER SIDE OF PRODUCTION METER 5()(5(1&(32,172)$33/,&$%,/,7< J-BOX STRING (1): 15.96 A AC, 14 MODULES STRING (2): 13.68 A AC, 11 MODULES N G 3 AC COMBINER BOX SOLAR LOADS ONLY UL 1741 COMPLIANT AC DC AC DC6 INVERTERS AC DC AC DC7 INVERTERS J-BOX (N) 100A (2) 20A-2P J-BOX1 2 1 2 4 (E) LOADS N G (E)GROUNDING ELECTRODE SUPPLY SIDE CONNECTION: NEC 230.46, NEC 230.79, NEC 705.12(A). .,170,/%$1. /8*.,772%($''(' (E) 200A-2P (E) 200A MAIN SERVICE PANEL (E) (E)UTILITY METER 120/240 VAC TO UTILITY GRID1-PH,240V RATED SERVICE Everlight Solar Construction PO Box 930550 Verona, WI 53593 License# DCQ-111802116 833.786.4387 ext. 701 CONTRACTOR INFORMATION: SITE INFORMATION Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC Lat, 44.64597 Long, -93.2496805999999 (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) Xcel Energy MN DATE: March 18, 2022 LINE DIAGRAM - PV05 DRAWN BY: SoloCAD AP Systems YC600 Specs MAX INPUT VOLTAGE:55 V MAX DC SHORT CIRCUIT CURRENT:12 A MAXIMUM OUTPUT POWER:548 W MAXIMUM OUTPUT CURRENT:2.28 A NOM. OUTPUT VOLTAGE:240 V MAX UNITS PER 20A CIRCUIT:7 1-Phase, 60 HZ, UL 1741 Listed Mission Solar MSE345SX5T Specs POWER MAX (PMAX):345W OPEN CIRCUIT VOLTAGE (VOC):41V MAX POWER-POINT CURRENT (IMP):10.34A MAX POWER-POINT VOLTAGE (VMP):33.37V SHORT CIRCUIT CURRENT (ISC):10.92A SERIES FUSE RATING:20A VISIBLE, LOCKABLE, LABELED AC DISCONNECT LOCATED WITHIN 10' OF UTILITY METER Conduit & Conductor Schedule TAG QTY WIRE GAUGE DESCRIPTION CONDUIT SIZE 1 (2)12-2 TC-ER, THWN-2, COPPER (L1, L2)N/A - FREE AIR(1)6 AWG THWN-2 COPPER - (GROUND) 2 (2)10 AWG THHN/THWN-2, COPPER - (L1, L2)3/4" EMT(1)10 AWG THWN-2 COPPER - (GROUND) 3 (4)10 AWG THHN/THWN-2, COPPER - (L1, L2)3/4" EMT(1)10 AWG THWN-2 COPPER - (GROUND) 4 (3)6 AWG THWN-2 COPPER - (L1, L2, NEUTRAL)3/4" EMT(1)8 AWG THWN-2 COPPER - (GROUND) 0 Equipment Schedule TYPE:QTY:DESCRIPTION:RATING: MODULES:(25)Mission Solar MSE345SX5T 345 W INVERTERS:(13)AP Systems YC600 548 W AC DISCONNECTS:(1)PV AC Disconnect, 240V, 2-Pole 60 A CASE# 04896762 DESIGN SHALL MEET NEC REQUIREMENTS ALL PV EQUIPMENT INSTALLED WITHIN 10' OF UTILITY METER ,17(5&211(&7,21127(6 1. GROUND FAULT PROTECTION IN ACCORDANCE WITH [NEC 215.9] & [NEC 230.95] 2. SUPPLY SIDE INTERCONNECTION ACCORDING TO [NEC705.12(A)] WITH SERVICE ENTRANCE CONDUCTORS IN ACCORDANCE WITH [NEC 240.21(B)] ',6&211(&7127(6 1. DISCONNECTING SWITCHES SHALL BE WIRED SUCH THAT WHEN THE SWITCH IS OPENED THE CONDUCTORS REMAINING LIVE ARE CONNECTED TO THE TERMINALS MARKED “LINE SIDE” (TYPICALLY THE UPPER TERMINALS) 2. AC DISCONNECT MUST BE ACCESSIBLE TO QUALIFIED UTILITY PERSONNEL, BE LOCKABLE, AND BE A VISIBLE-BREAK SWITCH. 3. FUSED AC DISCONNECT TO BE USED. *5281',1* *(1(5$/127(6 1. PV INVERTER IS UNGROUNDED, TRANSFORMER-LESS TYPE. 2. DC GEC AND AC EGC TO BE SPLICED TO EXISTING ELECTRODE 3. ANY EXISTING WIRING INVOLVED WITH PV SYSTEM CONNECTION THAT IS FOUND TO BE INADEQUATE PER CODE SHALL BE CORRECTED PRIOR TO FINAL INSPECTION. 4. JUNCTION BOX QUANTITIES, AND PLACEMENT SUBJECT TO CHANGE IN THE FIELD - JUNCTION BOXES DEPICTED ON ELECTRICAL DIAGRAM REPRESENT WIRE TYPE TRANSITIONS. 5. AC DISCONNECT NOTED IN EQUIPMENT SCHEDULE OPTIONAL IF OTHER AC DISCONNECTING MEANS IS LOCATED WITHIN 10' OF SERVICE DISCONNECT. STRING CALCULATIONS MAX AC CURRENT: MICRO INVERTERS IN SERIES NOMINAL STRING VOLTAGE: MAX AC OUTPUT POWER ARRAY DC POWER: TOTAL MAX AC CURRENT: STRING #1 15.96A 7 240V 3836W 8625W 29.64A STRING #2 13.68A 6 240V 3288W AP Systems YC600 Everlight Solar Construction PO Box 930550 Verona, WI 53593 License# DCQ-111802116 833.786.4387 ext. 701 CONTRACTOR INFORMATION: SITE INFORMATION Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC Lat, 44.64597 Long, -93.2496805999999 (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) Xcel Energy MN DATE: March 18, 2022 ELECTRICAL CALCS - PV06 DRAWN BY: SoloCAD Conduit & Conductor Schedule TAG QTY WIRE GAUGE DESCRIPTION CONDUIT SIZE CONDUCTOR RATING CONDUCTOR TEMP. RATE AMBIENT TEMP TEMP. DERATE # OF CONDUCTORS DERATE CONDUCTOR RATING W/DERATES CONDUIT FILL 1 (2)12-2 TC-ER, THWN-2, COPPER (L1, L2)N/A - FREE AIR 30A 90°C 32°C 0.96 N/A - FREE AIR 28.8A N/A - FREE AIR(1)6 AWG THWN-2 COPPER - (GROUND) 2 (2)10 AWG THHN/THWN-2, COPPER - (L1, L2)3/4" EMT 40A 90°C 32°C 0.96 1 38.4A 11.9%(1)10 AWG THWN-2 COPPER - (GROUND) 3 (4)10 AWG THHN/THWN-2, COPPER - (L1, L2)3/4" EMT 40A 90°C 32°C 0.96 0.8 30.72A 19.8%(1)10 AWG THWN-2 COPPER - (GROUND) 4 (3)6 AWG THWN-2 COPPER - (L1, L2, NEUTRAL)3/4" EMT 65A 75°C 32°C 0.96 1 62.4A 35.5%(1)8 AWG THWN-2 COPPER - (GROUND) SYSTEM OCPD CALCULATIONS INVERTER MODEL(S):AP Systems YC600 # OF INVERTERS:13 MAX OUTPUT CURRENT:2.28A (# OF INVERTERS) X (MAX OUTPUT CURRENT) X 125% <= OCPD RATING (13 X 2.28A X 1.25) = 37.05A <= 40A, OK SUPPLY SIDE INTERCONNECTION MAIN BUSBAR RATING:200A MAIN DISCONNECT RATING:200A PV OCPD RATING:40A SERVICE RATING >= PV OCPD 200A >= 40A, OK NUMBER OF CURRENT CARRYING CONDUCTORS PERCENT OF VALUES 4-6 .80 7-9 .70 10-20 .50 Everlight Solar Construction PO Box 930550 Verona, WI 53593 License# DCQ-111802116 833.786.4387 ext. 701 CONTRACTOR INFORMATION: SITE INFORMATION Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC Lat, 44.64597 Long, -93.2496805999999 (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) Xcel Energy MN DATE: March 18, 2022 LABELS - PV07 DRAWN BY: SoloCAD LABEL 3 AT POINT OF INTERCONNECTION, MARKED AT AC DISCONNECTING MEANS. [NEC 690.54, NEC 690.13 (B)] LABEL 4 AT POINT OF INTERCONNECTION FOR EQUIPMENT CONTAINING OVERCURRENT DEVICES IN CIRCUTS SUPPLYING POWER TO A BUSBAR OR CONDUCTOR SUPPLIED FORM MULTIPLE SOURCES, EACH SERVICE EQUIPMENT AND ALL ELECTRIC POWER PRODUCTION SOURCE LOCATIONS. [NEC 705.12(B)(3)] LABEL 5 PLACED ADJACENT TO THE BACK-FED BREAKER FROM THE INVERTER IF TIE IN CONSISTS OF LOAD SIDE CONNECTION TO BUSBAR. [NEC 705.12(D)(2)(3)(b)] *ELECTRICAL DIAGRAM SHOWN ABOVE IS FOR LABELING PURPOSES ONLY. NOT AN ACTUAL REPRESENATION OF EQUIPMENT AND CONNECTIONS TO BE INSTALLED. LABEL LOCATIONS PRESENTED MAY VERY DEPENDING ON TYPE OF INTERCONNECTION METHOD AND LOCATION PRESENTED ON PV5 OF 3 LINE DIAGRAM. PV5 LINE DIAGRAM TO REFLECT ACTUAL REPRESENTATION OF PROPOSED SCOPE OF WORK. JUNCTION BOX OR COMBINER BOX MAIN SERVICE PANEL AC DISCONNECT EXISTING SUB PANEL (IF WHERE POINT OF INTERCONNECTION IS MADE) PV COMBINER SUBPANEL - IF USED TO COMBINE PV OUTPUT CIRCUITS AC DC INVERTER (S) INTEGRATED DC DISCONNECT 2 3 47 3 9 5 (ONLY IF PV INTERCONNECTION CONSISTS OF LOAD SIDE BREAKER) 6 10 1 1 1 1 4 5 (ONLY IF PV INTERCONNECTION CONSISTS OF LOAD SIDE BREAKER) 4 6 3 LABELING DIAGRAM: 12 11 8OR LABEL 6 AT DIRECT-CURRENT EXPOSED RACEWAYS, CABLE TRAYS, COVERS AND ENCLOSURES OF JUNCTION BOXES, AND OTHER WIRING METHODS; SPACED AT MAXIMUM 10FT SECTION OR WHERE SEPARATED BY ENCLOSURES, WALLS, PARTITIONS, CEILINGS, OR FLOORS. [NEC 690.31(G)(3&4)] LABEL 10 (ONLY IF 3 OR MORE SUPPLY SOURCES TO A BUSBAR) SIGN LOCATED AT LOAD CENTER IF IT CONTAINS 3 OR MORE POWER SOURCES. [NEC 705.12(D)(2)(3)(C)] LABEL 9 SIGN LOCATED AT RAPID SHUT DOWN DISCONNECT SWITCH [NEC 690.56(C)(3)]. LABEL 7 FOR PV SYSTEMS THAT SHUT DOWN THE ARRAY AND CONDUCTORS LEAVING THE ARRAY: SIGN TO BE LOCATED ON OR NO MORE THAN 3 FT AWAY FROM SERVICE DISCONNECTING MEANS TO WHICH THE PV SYSTEMS ARE CONNECTED AND SHALL INDICATE THE LOCATION OF ALL IDENTIFIED RAPID SHUTDOWN SWITCHES IF NOT AT THE SAME LOCATION. [NEC 690.56(C)(1)(A)] LABEL 8 FOR PV SYSTEMS THAT ONLY SHUT DOWN CONDUCTORS LEAVING THE ARRAY: SIGN TO BE LOCATED ON OR NO MORE THAN 3 FT AWAY FROM SERVICE DISCONNECTING MEANS TO WHICH THE PV SYSTEMS ARE CONNECTED AND SHALL INDICATE THE LOCATION OF ALL IDENTIFIED RAPID SHUTDOWN SWITCHES IF NOT AT THE SAME LOCATION. [NEC 690.56(C)(1)(B)] LABEL 11 PLACARD TO BE PLACED AT THE MAIN BILLING METER PER XCEL ENERGY. LABEL 12 PLACARD TO BE PLACED AT AC DISCONNECT PER XCEL ENERGY. LABEL 1 FOR PV DISCONNECTING MEANS WHERE ALL TERMINALS OF THE DISCONNECTING MEANS MAY BE ENERGIZED IN THE OPEN POSITION. [NEC 690.13(B), NEC 705.22] LABEL 2 AT EACH DC DISCONNECTING MEANS, INCLUDING THE DC DISCONNECT AT THE INVERTER. [NEC 690.53, NEC 690.13(B)] LABEL 13 SIGN LOCATED AT MAIN SERVICE DISCONNECTING MEANS IF ALL ELECTRICAL POWER SOURCE DISCONNECTING MEANS ARE GROUPED WITHIN 10' AND LINE OF SITE OF MAIN SERVICE DISCONNECT [NEC 690.56(B) & NEC 705.10]. LABEL 14 SIGN LOCATED AT AC COMBINER BOX FOR ALL MICRO-INVERTER / AC MODULE INSTALLS (IF APPLICABLE). 13 14 LABELING NOTES: 1.LABELS CALLED OUT ACCORDING TO ALL COMMON CONFIGURATIONS. ELECTRICIAN TO DETERMINE EXACT REQUIREMENTS IN THE FIELD PER CURRENT NEC AND LOCAL CODES AND MAKE APPROPRIATE ADJUSTMENTS. 2.LABELING REQUIREMENTS BASED ON THE 2014 NATIONAL ELECTRIC CODE, OSHA STANDARD 19010.145, ANSI Z535. 3.MATERIAL BASED ON THE REQUIREMENTS OF THE AUTHORITY HAVING JURISDICTION. 4.LABELS TO BE OF SUFFICIENT DURABILITY TO WITHSTAND THE ENVIRONMENT INVOLVED [NEC 110.21] 5.LABELS TO BE A MINIMUM LETTER HEIGHT OF 3/8", WHITE ON RED BACKGROUND; REFLECTIVE, AND PERMANENTLY AFFIXED [IFC 605.11.1.1] 3 4 1 :$51,1*! 7(50,1$/6217+(/,1($1' /2$'6,'(60$<%((1(5*,=(' ,17+(23(1326,7,21 (/(&75,&6+2&.+$=$5' ! 5$7('$&287387&855(17 $ 120,1$/23(5$7,1*$&92/7$*(9 3+27292/7$,&6<67(0 $&',6&211(&7 ! :$51,1*! :$51,1*3+27292/7$,& 32:(56285&( TURN RAPID SHUTDOWN SWICH TO THE "OFF" POSITION TO SHUT DOWN PV SYSTEM AND REDUCE SHOCK HAZARD IN ARRAY 62/$5396<67(0(48,33(' :,7+5$3,'6+87'2:1 62/$5(/(&75,& 393$1(/6 TURN RAPID SHUTDOWN SWITCH TO THE "OFF" POSITION TO SHUT DOWN CONDUCTORS OUTSIDE THE ARRAY. CONDUCTORS WITHIN THE ARRAY REMAIN ENERGIZED IN SUNLIGHT 62/$5396<67(0(48,33(' :,7+5$3,'6+87'2:1 62/$5(/(&75,& 393$1(/6 ! 5$3,'6+87'2:1 6:,7&+)25 62/$5396<67(0 !:$51,1* 7+,6(48,30(17,6)('%<08/7,3/( 6285&(6727$/5$7,1*2)$// 29(5&855(17'(9,&(6(;&/8',1* 0$,16833/<29(5&855(17 '(9,&(6+$//127(;&((' $03$&,7<2)%86%$5 3+27292/7$,& 6<67(0&211(&7(' 87,/,7<$&',6&211(&7 5$3,'6+87'2:17(67 1275(48,5('&$87,21 $//(/(&75,&32:(56285&( ',6&211(&7,1*0($16*5283(' $1'/$%(/(':,7+,1)7$1' /,1(2)6,*+72)7+,6/2&$7,21 ',5(&7&855(17 3+27292/7$,&32:(56285&( 0$;,08092/7$*(9'& 0$;&,5&8,7&855(17$036 12'&:,5(635(6(17 !:$51,1* ,19(57(5287387&211(&7,21 '21275(/2&$7( 7+,629(5&855(17 '(9,&( '8$/32:(56833/< 6285&(687,/,7<*5,'$1'39 62/$5(/(&75,&6<67(0 0 0 30 240 352'8&7,210(7(5 LABEL 15 PLACARD TO BE PLACED AT BI-DIRECTIONAL METER PER XCEL ENERGY. M MSP ACC PV JB JB Everlight Solar Construction PO Box 930550 Verona, WI 53593 License# DCQ-111802116 833.786.4387 ext. 701 CONTRACTOR INFORMATION: SITE INFORMATION Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC Lat, 44.64597 Long, -93.2496805999999 (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) Xcel Energy MN DATE: March 18, 2022 POWER TO THIS BUILDING IS ALSO SUPPLIED FROM ROOF MOUNTED SOLAR ARRAYS WITH SAFETY DISCONNECTS AS SHOWN: CAUTION DIRECTORY PERMANENT PLAQUE OR DIRECTORY PROVIDING THE LOCATION OF THE SERVICE DISCONNECTING MEANS AND THE PHOTOVOLTAIC SYSTEM. (ALL PLAQUES AND SIGNAGE WILL BE INSTALLED AS OUTLINED WITHIN: NEC 690.56(B)&(C), [NEC 705.10])FRONT OF HOMERAPID SHUTDOWN AC DISCONNECT SWITCH 20984 Hyacinth Avenue, Lakeville MN 55044 PLACARD - PV08 DRAWN BY: SoloCAD MAIN DISTRIBUTION UTILITY DISCONNECT PV ARRAY COMBINER Everlight Solar Construction PO Box 930550 Verona, WI 53593 License# DCQ-111802116 833.786.4387 ext. 701 CONTRACTOR INFORMATION: SITE INFORMATION Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC Lat, 44.64597 Long, -93.2496805999999 (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) Xcel Energy MN DATE: March 18, 2022 SITE PHOTOS: SITE PHOTOS - PV09 DRAWN BY: SoloCAD Everlight Solar Construction PO Box 930550 Verona, WI 53593 License# DCQ-111802116 833.786.4387 ext. 701 CONTRACTOR INFORMATION: SITE INFORMATION Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC Lat, 44.64597 Long, -93.2496805999999 (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) Xcel Energy MN DATE: March 18, 2022 SITE PHOTOS: FRONT/BACK VIEWS - PV09.1 DRAWN BY: SoloCAD Everlight Solar Construction PO Box 930550 Verona, WI 53593 License# DCQ-111802116 833.786.4387 ext. 701 CONTRACTOR INFORMATION: SITE INFORMATION Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC Lat, 44.64597 Long, -93.2496805999999 (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) Xcel Energy MN DATE: March 18, 2022 SITE PHOTOS: SIDE VIEWS - PV09.2 DRAWN BY: SoloCAD Contact Info and General 1.Name of Customer who owns service, the Xcel Energy “customer of record” for existing services 2.Installation premise address shall match application address 2.1 Address shall match the premise address for existing customer/services 3.Application OID, SRC, or case number assigned to the project 4.A note stating “All testing shall be performed by qualified personnel" Testing Applicable to all DER 5.The procedure shall provide steps to verify fixed power factor settings for each inverter meet the project requirements 6.The unintentional islanding test shall at minimum contain the following steps: 6.1 Steps that verify DER system is ready to be energized 6.2 Steps to verify labeling for the Main Service Panel, DER Protection, DC Disconnect, AC disconnect, Utility AC disconnect, Production Meter (when applicable) and other relevant labelling and signage 6.3 Steps to energize the DER system 6.4 While in normal operation, steps to verify the voltages at the DER AC terminals are within 5% of the combined DER AC voltage ratings and all LEDs, alarms, and/or LCD codes are “normal” 6.5 While in normal operation, steps to verify that all DER units are operational and producing power 6.6 Steps to simulate the loss of utility source11 for the unintentional islanding test shall be listed 6.6.1 Clearly identify the disconnection device being used to simulate this utility power outage 6.7 Using a voltmeter, verify the voltage at the inverter side of the AC disconnect has dropped to zero 6.7.1 Only customer-owned equipment shall be used for this verification. Xcel Energy will not provide special equipment for this verification. Xcel Energy provided meters shall not be used for this verification. 6.8 Using an ammeter or the DER’s display/metering, verify the DER has ceased to energize within two seconds. For three phase systems, three phase monitoring may be required. 7.Verify DER LEDs, alarms, and/or LCD codes are appropriate for loss of Utility source 8.Steps to restore the lost Utility source shall be listed 9.A step to verify that the inverter system delays five (5) minutes before resuming power output after the Utility source is restored shall be listed Everlight Solar Construction PO Box 930550 Verona, WI 53593 License# DCQ-111802116 833.786.4387 ext. 701 CONTRACTOR INFORMATION: SITE INFORMATION Benjamin Rietz 20984 Hyacinth Avenue Lakeville, MN 55044 AC SYSTEM SIZE: 7.124 kW AC DC SYSTEM SIZE: 8.625 kW DC Lat, 44.64597 Long, -93.2496805999999 (25) Mission Solar MSE345SX5T PV MODULES (13) AP Systems YC600 INVERTER(S) Xcel Energy MN DATE: March 18, 2022 CASE#04896762 METER/OPEN MSP - PV09.3 DRAWN BY: SoloCAD THESE SHEETS, DESIGNS, AND SPECS ARE PROPERTY OF SUN INCORPORATED. NO PART SHALL BE DUPLICATED OR USED FOR NONE OTHER THAN ITS SPECIFIC PROJECT WITHOUT WRITTEN CONSENT FROM SUN INCORPORATED.MOUNT SHEETSheet: 5File: SUN-SERVERSun Incorporated Jos MasterEuipmentMOUNTSQUICK MOUNTQMPV-datasheet-QMHSS-LS-QuicHooSM-we.pdMissing or invalid reerenceSheet: 2File: SUN-SERVERSun Incorporated Jos MasterEuipmentMOUNTSQUICK MOUNTQMPV-datasheet-QMHSS-LS-QuicHooSM-we.pdMissing or invalid reerence